MHT2-Z, pinza pneumatica, a trasmissione articolata (MHT2-63TNDZ-X4)

MHT2-Z, pinza pneumatica, a trasmissione articolata MHT2-63TNDZ-X4

Dettagli del prodotto:

Codice articolo del costruttore: MHT2-63TNDZ-X4

Marca: SMC

Prezzo: 693.03

Tempi di consegna: 26 giorni


Dati Tecnici:

Forza di presa (con chiusura a 0.5Mpa): 10,600 N

Diametro interno cilindro: 63 mm

Interruttore automatico: Senza interruttore automatico (magnete incorporato)

Numero di interruttori: Assente

Lunghezza filo conduttore: Assente


(i)Nota

  • Refer to the catalog for details on product specifications.
  • Product images may be representative. Refer to the manufacturer's catalog for details.

Codice componente

Qui sono indicati i codici componente
correlati al prodotto ricercato

MHT2-63TNDZ-X4

MHT2 Series Toggle Type Air Chuck Specifications

MHT2 Series JIS symbol (double acting, external gripping)

MHT2 Series JIS symbol (double acting, external gripping)

Model MHT2-32DZ MHT2-40DZ MHT2-50DZ MHT2-63DZ
Bore size (mm) 32 40 50 63
Operating method Double acting type
Applicable fluids Air
Operating pressure 0.1 to 0.6 MPa
Ambient temperature and working fluid temperature 5 to 60°C
Lubrication Non-lube
Finger opening angle (both sides) -3° to +28 °-3° to 27 °-2° to 23 °-2° to 23 °
Weight (g) 790 1,070 1,890 2,720
Gripping moment (effective value) N· mNote) 12.4 36.0 63.0 106

Note) Value at pressure of 0.5 MPa

Outline dimensional drawing

 

(Unit: mm)

 

MHT2-32DZ dimensional drawing

MHT2-32DZ dimensional drawing

 

(Unit: mm)

 

MHT2-40DZ dimensional drawing

MHT2-40DZ dimensional drawing

Effective Gripping Force

L: Gripping point length dimensional drawing

L: Gripping point length dimensional drawing

  • *Workpiece gripping point should be within the range indicated in the graph.
  • *If there is an overhang, please consult with the manufacturer's support center.
Finger thrust: F diagram

Finger thrust: F diagram

The effective gripping force shown in the graphs below is expressed as F, which is the thrust of one finger when both fingers and attachments are in full contact with the workpiece as shown in the figure above.

MHT2-32DZ effective gripping force graph

MHT2-32DZ effective gripping force graph

When L = 100 mm

MHT2-40DZ effective gripping force graph

MHT2-40DZ effective gripping force graph

When L = 120 mm

MHT2-50DZ effective gripping force graph

MHT2-50DZ effective gripping force graph

When L = 150 mm

MHT2-63DZ effective gripping force graph

MHT2-63DZ effective gripping force graph

When L = 180 mm

Structural drawing

MHT2 Series structure drawing

MHT2 Series structure drawing

Number Part name Material Note
1 Side plate Aluminum Alloy Hard anodizing
2 Finger Carbon steel Black zinc chromate
3 Lever Carbon steel Black zinc chromate
4 Joint Carbon steel Black zinc chromate
5 Shaft Stainless steel -
6 Joint pin Stainless steel -
7 Cylinder plate Soft steel Black zinc chromate
8 Lever pin Stainless steel -
9 Shaft - Steel lined oil-impregnated acetal resin bearing
10 Shaft - Steel lined oil-impregnated acetal resin bearing
11 Cylinder - Compact cylinder

Attachment Design

  1. 1. Design the attachment so that both fingers grip the workpiece when they are in parallel with each other.
  2. 2. Take care to enable fine adjustment of the attachment by inserting an adjustment shim, etc.
  3. 3. If the shim is too thin, the gripping force becomes insufficient and the workpiece may become unstable. Conversely, if the shim is too thick, the toggle mechanism is difficult to activate and a large impact sound may sometimes be produced. Carefully check this point.
  4. 4. The gripping status may become unstable due to continual wear of the bearing or shaft during operation. If this happens, make adjustments such as using a thicker shim according to the conditions.

Precautions

  • *When the toggle is used to grip a workpiece, if the rod is pushed or a load is placed on it, the toggle mechanism may not work. This may result in shifting or dropping the workpiece, which could be dangerous.
  • *If the grip is unstable, use shims, etc. to adjust the attachment.
  • *To verify the gripping condition or to make any adjustments, make sure to do so in an area where the air chuck or the workpiece will not fall.
  • *Be sure to read the product-specific precautions in the manufacturer's catalog before use.
  • *See the manufacturer's catalog for product information other than the above.
Codice componente
MHT2-63TNDZ-X4
Codice componenteRelativo a
Prezzo unitario standard
Quantità minima d'ordineSconto volumi elevati
Giorni
spedizione standard
?
Forza di presa (con chiusura a 0.5Mpa)
(N)
Diametro interno cilindro
(mm)
Interruttore automatico Numero di interruttori Lunghezza filo conduttore Specifiche su ordinazione Tipo di connettore per apertura / chiusura pinza Tipo filettatura raccordo
-

693.03 €

1 26 giorni 10,60063Senza interruttore automatico (magnete incorporato)AssenteAssenteTermoresistenza (100°C)AssenteNPT

Loading...

  1. 1

Informazioni di base

Tipo di presa Presa a pinza, orientabile Numero di dita di presa 2 pz. Profilo corpo principale Profilo quadrato
Metodo di funzionamento A doppia azione Ambiente, applicazioni Standard Funzione aggiuntiva Non in dotazione
Meccanismo di regolazione corsa Non in dotazione

Si trova sulla pagina di MHT2-Z, pinza pneumatica, a trasmissione articolata, il codice articolo è il seguente: MHT2-63TNDZ-X4.
Ulteriori dettagli concernenti specifiche e dimensioni si trovano sotto il codice prodotto MHT2-63TNDZ-X4.

Tipologia prodotto

Codice componente
MHT2-32DZ
MHT2-32DZ-A93L
MHT2-32DZ-A93VL
MHT2-32DZ-M9B
MHT2-32DZ-M9BL
MHT2-32DZ-M9BVSDPC
Codice componenteRelativo a Prezzo unitario standardQuantità minima d'ordineSconto volumi elevatiGiorni
spedizione standard
?
Forza di presa (con chiusura a 0.5Mpa)
(N)
Diametro interno cilindro
(mm)
Interruttore automatico Numero di interruttori Lunghezza filo conduttore Specifiche su ordinazione Tipo di connettore per apertura / chiusura pinza Tipo filettatura raccordo

469.81 €

1 4 giorni 1,24032Senza interruttore automatico (magnete incorporato)AssenteAssenteAssenteAssenteRc
-

516.10 €

1 26 giorni 1,24032A932 pz.3 mAssenteAssenteRc
-

516.10 €

1 26 giorni 1,24032A93V2 pz.3 mAssenteAssenteRc

531.84 €

1 26 giorni 1,24032M9B2 pz.0.5 mAssenteAssenteRc
-

539.24 €

1 26 giorni 1,24032M9B2 pz.3 mAssenteAssenteRc
-

555.53 €

1 26 giorni 1,24032M9BV2 pz.0.5 mAssenteM12 4 pinRc

Supporto tecnico