GANTER Piedi di livellamento, ancoraggi

?* Informazioni su tempi di consegna e prezzi

• • In Offerta

  

  Ball jointed levelling feet, Plastic / Steel

  GANTER

  Ball jointed levelling feet GN 638 feature a smaller size ball diameter than the trunk of the threaded stud. As a result the studs can be screwed into position from the ball side. The ball end can easily be hammered in and also dismantled.
  Details regarding the static load capacity have been established by a series of tests but are indicative only. For these tests the loads have been placed vertically and centrally over the stud. At the measured load of 3,5 kN there was no remaining deformation visible on the thrust pad nor was there any breakage.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	2.22 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Leveling feet, foot / threaded stud Stainless Steel

  GANTER

  The static load of the levelling feet GN 343.6 is limited by the laod capacity of the Stainless Steel ball joint with threaded stud (AISI 303).
  The static load values in the above table refer to a net vertical load in relation to the ball socket. Under normal operating conditions side loadting or angular loading is not uncommon and the load capacity would be considerable reduced which must be taken into consideration.
  Levelling feet GN 343.6 cannot be disassembled.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	13.54 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Levelling feet, threaded bushing steel

  GANTER

  Levelling feet GN 343.1 cannot be disassembled.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	5.90 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• 

  Spherical levelling washers, Steel

  GANTER

  Spherical levelling washers GN 350.3 have been designed to match the levelling sets GN 350, GN 350.1, GN 350.2 and GN 350.5.
  The two spherical washers are used together „undetachably“.
  The load bearing capacity of these spherical washers is relatively high. This is not only due to the material quality but also to the matched sphere of the concave „pan“.
  Furthermore it is recommended using high-strength washers for bridging d2.
  

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	17.62 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Ball jointed levelling feet, Plastic, Stainless Steel

  GANTER

  Ball jointed levelling feet GN 638 feature a smaller size ball diameter than the trunk of the threaded stud. As a result the studs can be screwed into position from the ball side. The ball end can easily be hammered in and also dismantled.
  Details regarding the static load capacity have been established by a series of tests but are indicative only. For these tests the loads have been placed vertically and centrally over the stud. At the measured load of 3,5 kN there was no remaining deformation visible on the thrust pad nor was there any breakage.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	2.56 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• 

  Levelling elements, Steel

  GANTER

  Levelling elements GN 355 are used for levelling and adjustment in machines and equipment.
  They consist of a levelling screw, a cylinder screw with disk and a spherical washer. After making the adjustment using the assembly tools GN 355.1 available as accessory, the screw is tightened firmly causing the levelling screw and the spherical washer DIN 6319 underneath to spread and is so secured against twisting in the taphole.
  The values for w and x given in the table and for the static load capacity are to be seen as reference values which may differ depending on the prevailing situation. In general, they do not constitute a warranty of condition. The user must determine whether the product is suitable for the intended purpose.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	16.26 €
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Levelling feet with threaded stud, Steel

  GANTER

  The static load of the levelling feet GN 343.2 is limited by the load capacity of the ball joint with threaded stud (tensile strength class 5.8 (500 N/mm2)).
  The static load values (only valid for Type OS / KS) in the above table refer to a net vertical load in relation to the levelling foot. Under normal operating conditions side loading or angular loading is not uncommon and the load capacity would be considerably reduced which must be taken into consideration.
  Levelling feet GN 343.2 cannot be disassembled.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	6.42 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Levelling feet with mounting lug

  GANTER

  Levelling feet GN 32 will be delivered mounted and are not removable.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	10.76 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• 

  Levelling feet without mounting holes, Hygienic Design

  GANTER

  GN 20 levelling feet without mounting holes are intended for use in hygiene areas. The bottom seal protects the area beneath the foot plate from dirt. For this, the foot must be screwed on using the mounting holes and compressed accordingly. Hygienic fastenings and the correct position of the mounting holes are essential. The sealing ring above the adjustment sleeve enables fastening without dead space. Due to the wiper or the ball seal, the moving components are sealed against the environment.
  The high quality finish prevents adherence of dirt and facilitates cleaning.
  The values listed in the table for static load capacity refer to a purely vertical load in relation to the leveling foot. Under normal operating conditions bending loads or angular loads are not uncommon and result in a reduction of load capacity, which must be taken into consideration.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	132.30 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• 

  Levelling feet with fixing lug, Steel, zinc plated, rectangular shape (GN 42)

  GANTER

  GN 42 levelling feet can be used in a host of combinations of base plates and adjustable spindle versions.
  >The levelling feet can be screwed to the mounting surface use the fixing lug, which prevents lateral shifting. Moreover, the types with the rubber underlay protect sensitive surfaces.
  The levelling feet are supplied fully assembled and are not removable.

  • Sconto volumi elevati

  A partire da∗ ：	11.48 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• 

  Adjustment plates for bull´s eye levels GN 2277

  GANTER

  Adjustment plates GN 2277.1 are used in combination with bull´s eye levels GN 2277, Type A.
  The mounting bore holes offset by 120° allow the bull‘s eye levels and the mounting plate to be aligned in relation to the mounting surface. An alignment ball at the bottom surface of the adjustment plate serves as tilting point. Specific tightening torques of the bolts allow to be achieved, so that the bubble is located inside the marking ring once the horizontal alignment is reached.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	4.02 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Bull´s eye levels

  GANTER

  Bull´s eye levels GN 2277 are used to check the horizontal position of jigs, machines, devices, appliances and instruments.
  The spirit levels are aligned in relation to the reference surface so that the bubble is located inside the marking ring when the horizontal position of the contact surface is achieved.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	13.16 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• 

  Bull´s eye levels

  GANTER

  Bull´s eye levels GN 2279 are used to check the horizontal position of jigs, machines, devices, appliances and instruments.
  Type A is used if the spirit level is to be used as a tool, e.g. at different measuring points.
  The spirit levels are aligned in relation to the reference or contact surface, such that the bubble is located inside the marking ring once the horizontal position of the contact surface is reached.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	10.76 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• 

  Levelling feet with mounting holes, Hygienic Design

  GANTER

  GN 20 hygienic leveling feet with mounting holes are certified according to EHEDG guidelines and are therefore ideal for use in hygienic applications.
  The bottom seal protects the area beneath the foot plate from dirt. For this, the foot must be screwed on using the mounting holes and compressed accordingly. Hygienic fastenings and the correct position of the mounting holes are essential. The sealing ring above the adjustment sleeve enables fastening without dead space. Due to the wiper or the ball seal, the moving components are sealed against the environment.
  The high quality finish prevents adherence of dirt and facilitates cleaning.
  The values listed in the table for static load capacity refer to a purely vertical load in relation to the leveling foot. Under normal operating conditions bending loads or angular loads are not uncommon and result in a reduction of load capacity, which must be taken into consideration.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	166.02 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Levelling feet with mounting lug, steel sheet, zinc plated, with and without rub

  GANTER

  Levelling feet GN 42 will be delivered mounted and are not removable.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	5.82 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Levelling feet with vibration absorbing

  GANTER

  The specified load in the above table is a recommendation up to which the damping insert can be permanently subjected.
  This static load equals a thrust on the area of 0,4 N/mm2, at which the damping material reaches its optimum dynamic damping ability. This also takes into account an additional load up to 0,6 N/mm2 in the event of a dynamic load.
  Levelling feet GN 342.2 cannot be disassembled.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	15.00 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Levelling feet with vibration absorbing, Steel

  GANTER

  The specified load in the above table of the levelling feet GN 342.1 is a recommendation up to which the damping element can be permanently subjected.
  This static load equals a thrust on the area of 0,4 N/mm2, at which the damping material reaches its optimum dynamic damping ability. This also takes into account an additional load up to 0,6 N/mm2 in the event of a dynamic load.
  Levelling feet GN 342.1 can not be disassembled.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	13.76 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Levelling feet, foot / threaded bushing Stainless Steel

  GANTER

  Levelling feet GN 343.5 cannot be disassembled.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	11.14 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Levelling feet, foot plastic / threaded bushing steel

  GANTER

  Levelling feet GN 343.3 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a larger area.
  Exceeding the static values specified in the above table could lead to failure of the plastic component.
  The above values have been arrived at by a series of load tests whereby a defined number of levelling feet were subjected to a vertical load over a defined period.
  Levelling feet GN 343.3 are supplied assembled, but are removable.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	2.92 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Levelling feet, Steel

  GANTER

  Levelling feet GN 30 will be delivered mounted and are not removable.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	10.50 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Levelling feet, Steel

  GANTER

  Levelling feet GN 339 are used for applications in cases where no jointed link is required between foot and adjusting screw.
  For this reason they offer the advantage of reduced height.
  The gliding and/or the non-gliding protective cap is safely fixed in the foot.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	7.80 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Levelling feet, steel sheet, zinc plated with and without rubber underlay

  GANTER

  Levelling feet GN 40 are easy and very reasonably priced foot design variants.
  Theywill be delivered mounted and are not removable.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	4.68 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Levelling feet, threaded bushing Stainless Steel

  GANTER

  Levelling feet GN 343.7 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a larger area.
  Exceeding the static values specified in the above table could lead to failure of the plastic component.
  The above values have been arrived at by a series of load tests whereby a defined number of levelling feet were subjected to a vertical load over a defined period.
  Levelling feet GN 343.7 are supplied assembled, but are removable.
  
  The static load of the levelling feet GN 343.7 / GN 343.8 is limited by the load capacity of the Stainless Steel ball joint (AISI 303). The static load values in the above table refer to a net vertical load in relation to the
  levelling foot. Under normal operating conditions side loading or angular loading is not uncommon and the load capacity would be considerably reduced which must be taken into consideration.
  Levelling feet GN 343.7 / GN 343.8 cannot be disassembled.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	3.98 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• 

  Levelling sets with spherical washer

  GANTER

  Levelling sets GN 350.2 are used for levelling, adjusting and linking operations. The spherical washer allows precise installation of two non parallel planes at a required gradient up to ≈ 4°.
  They comprise a threaded upper sleeve and a female threaded lower sleeve. The fine thread allows a stepless and precise setting and locking using the C-Spanner DIN 1810. A locking ring serves as a height limiter for the max. height.
  

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	47.16 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• 

  Levelling sets with spherical washer, with locknut

  GANTER

  Levelling sets GN 350.5 are used for levelling, adjusting and linking operations. The spherical washer allows precise installation of two non parallel planes at a required gradient up to ≈ 4°.
  They comprise a threaded upper sleeve and a female threaded lower sleeve. The fine thread allows a stepless and precise setting and locking using the C-Spanner DIN 1810. A locking ring serves as a height limiter for the max. height.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	69.92 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• 

  Levelling sets, long version

  GANTER

  Levelling sets GN 350 are used for levelling and linking operations. They comprise a threaded upper sleeve and a female threaded lower sleeve. The fine thread allows a stepless and precise setting and locking using the C-Spanner DIN 1810. A locking ring serves also as a height limiter for the max. height.
  Normally this screw is permanently and securely locked by the static load created when the mounting screw is tightened.
  Should this not be sufficient, the use of a locknut (Type AK) is recommended.
  

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	39.22 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• 

  Levelling sets, short version

  GANTER

  Levelling sets GN 350.1 are used for levelling, adjusting and linking operations if small dimensions are given.
  They comprise a threaded upper sleeve and a female threaded lower sleeve. The fine thread allows a stepless and precise setting and locking using the C-Spanner DIN 1810. A locking ring serves as a height limiter for the max. height.
  

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	31.72 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Mounts for leveling feet

  GANTER

  GN 349 mounts are used on levelling feet particularly in such cases where a machine shrouding is made of very thin sheet metal.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	11.98 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• 

  Stainless Steel-Levelling elements

  GANTER

  Levelling elements GN 355 are used for levelling and adjustment in machines and equipment.
  They consist of a levelling screw, a cylinder screw with disk and a spherical washer. After making the adjustment using the assembly tools GN 355.1 available as accessory, the screw is tightened firmly causing the levelling screw and the spherical washer DIN 6319 underneath to spread and is so secured against twisting in the taphole.
  The values for w and x given in the table and for the static load capacity are to be seen as reference values which may differ depending on the prevailing situation. In general, they do not constitute a warranty of condition. The user must determine whether the product is suitable for the intended purpose.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	19.58 €
  Consegna da ：	4 giorni

  *Prezzo unitario in configurazione base

• 

  Stainless Steel-Levelling feet

  GANTER

  Stainless Steel-Levelling feet GN 21 will be delivered mounted and are not removable.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	47.66 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Stainless Steel-Levelling feet

  GANTER

  Stainless Steel-Levelling feet GN 23 will be delivered mounted and are not removable.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	51.64 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Stainless Steel-Levelling feet

  GANTER

  GN 31 Stainless Steel-Levelling feet with vulcanised rubber (Type B3, B4, C3 and C4) and screw version W feature fewer dead spots owing to their construction method and are also easier to clean.
  Stainless Steel-Levelling feet GN 31 will be delivered mounted and are not removable.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	12.82 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Stainless Steel-Levelling feet

  GANTER

  Levelling feet GN 339 are used for applications in cases where no jointed link is required between foot and adjusting screw.
  For this reason they offer the advantage of reduced height.
  The gliding and/or the non-gliding protective cap is safely fixed in the foot.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	13.40 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Stainless Steel-Levelling feet with mounting lug

  GANTER

  Stainless Steel-Levelling feet GN 33 will be delivered mounted and are not removable.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	14.38 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Stainless Steel-Levelling feet with mounting lug, with and without rubber underl

  GANTER

  Stainless Steel-Levelling feet GN 43 will be delivered mounted and are not removable.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	7.70 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Stainless Steel-Levelling feet, with and without rubber underlay

  GANTER

  Stainless Steel-Levelling feet GN 41 will be delivered mounted and are not removable.

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	6.30 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Stainless Steel-Spherical levelling washers

  GANTER

  Stainless Steel-Spherical levelling washers GN 350.3 have been designed to match the levelling sets GN 350, GN 350.1, GN 350.2 and GN 350.5.
  The two spherical washers are used together „undetachably“.
  The load bearing capacity of these spherical washers is relatively high. This is not only due to the material quality but also to the matched sphere of the concave „pan“.
  Furthermore it is recommended using high-strength washers for bridging d2.
  

  • Sconto volumi elevati

  Dati CAD disponibili in formato 2D / 3D

  A partire da∗ ：	25.68 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• 

  Levelling sets, Steel (GN 360)

  GANTER

  GN 360 Levelling sets are used for leveling and to compensate for any slope when setting up machines and systems.The thread d2 can also be used as a through-hole for attachment from below. The fine thread d3 laws precise adjustment and readjustment using a DIN 1810 C-Spanner. A circlip limits the maximum path of adjustment.

  • Sconto volumi elevati

  A partire da∗ ：	104.12 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• 

  Stainless Steel-Levelling feet with fixing lug, rectangular shape (GN 43)

  GANTER

  GN 43 Stainless Steel-Levelling feet are for use in aggressive environments. The range of combinations of base plates and adjustable spindle versions allows these levelling feat to be used in every situation.
  
  The levelling feet can be screwed to the mounting surface use the fixing lug, which prevents lateral shifting. Moreover, the types with the rubber underlay protect sensitive surfaces.
  
  The levelling feet are supplied fully assembled and are not removable.

  • Sconto volumi elevati

  A partire da∗ ：	14.58 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• • In Offerta

  

  Stainless Steel-Levelling feet, A4 (GN 44)

  GANTER

  GN 44 Stainless Steel-Levelling feet are for use in aggressive environments. The range of combinations of base plates and adjustable spindle versions allows these levelling feat to be used in every situation.
  
  The base plate with the rubber underlay protects sensitive surfaces and reduces lateral slippage. The type B0 can also be fastened to the mounting surface through two holes.
  
  The levelling feet are supplied fully assembled and are not removable.

  • Sconto volumi elevati

  A partire da∗ ：	6.40 €
  	Prezzo speciale
  Consegna da ：	Stesso giorno

  *Prezzo unitario in configurazione base

• 

  Stainless Steel-Levelling feet, A4, with fixing lug, drop shape (GN 45)

  GANTER

  GN 45 Stainless Steel-Levelling feet are for use in aggressive environments. The range of combinations of base plates and adjustable spindle versions allows these levelling feat to be used in every situation.
  
  The levelling feet can be screwed to the mounting surface use the fixing lug, which prevents lateral shifting. Moreover, the types with the rubber underlay protect sensitive surfaces.
  
  The levelling feet are supplied fully assembled and are not removable.

  • Sconto volumi elevati

  A partire da∗ ：	9.08 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• 

  Stainless Steel-Levelling sets (GN 360)

  GANTER

  GN 360 Stainless Steel-Levelling sets are used for leveling and to compensate for any slope when setting up machines and systems.The thread d2 can also be used as a through-hole for attachment from below. The fine thread d3 laws precise adjustment and readjustment using a DIN 1810 C-Spanner. A circlip limits the maximum path of adjustment.

  • Sconto volumi elevati

  A partire da∗ ：	122.36 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• 

  Elementi di livellamento in acciaio inox

  GANTER

  • Sconto volumi elevati

  A partire da∗ ：	30.06 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

• 

  Manicotti di copertura in acciaio inossidabile, design igienico

  GANTER

  • Sconto volumi elevati

  A partire da∗ ：	21.42 €
  Consegna da ：	7 giorni

  *Prezzo unitario in configurazione base

Loading...